PD6 Operation instruction1. Charge The camera could be recharged because it has a built-in rechargeable lithium battery, by following charging ways: (1) Charging by charger, use USB data line to connect with charger base, and then plug in the charger, (Blue lamp are bright constantly and red lamp flash slowly while charging, it will cost 3 hours to realize fully charged.) (2) Charging by connecting with computer, use USB data line to connect with computer, and then charge the camera directly under the USB flash disk condition. 2. Start-up Press slightly “P” key, red and blue lamp will both turn on, and then the camera will start initialization and in the condition of start-up preparation, meanwhile, blue lamp will be bright constantly, the camera will switch to stand-by mode immediately. Note: *Please ensure that T-flash (Micro SD) card has been inserted into camera, if not, the blue lamp will flash slowly and camera will auto power-off after 30 seconds. If TF card is inserted in after power on, it’s easy to cause dead halt. *T-flash (Micro SD) minimum available memory capacity is 8GB, maximum memory capacity is 64GB, as for the memory card sharing with other equipment, please be sure to format it before use. *It will cost some time to save file, please not continuously press operation key or pull out memory card while saving, it may cause saving failure, or incomplete saved file, or even dead halt. *Please put camera lens aim at object under the circumstance of adequate light, and keep more than 50 cm distance away from object, by which could obtain right photo and video with natural color , distinct and stable image. 3. Night Sight Opening and Closing After power on, short press “P” key under any mode, if blue and red lamp flash twice at same time, it means Night Sight opening, short press “P” key again, if blue and red lamp flash once at same time, it means Night Sight closing. The camera only has night sight effect after opening Night Sight. 4. Recording Under standby mode, short press top key, blue lamp will be bright constantly and red lamp will flash for 3 times, after that, all indicators will turn off, then camera will start to record. Short press top key while recording, blue lamp will be bright constantly after saving file, meanwhile, camera will switch to standby mode. Please repeat above procedure if you want to continue to record. (This camera could record continuously, and save once every 10 minutes until no power with automatic save. It supports cyclic cover recording function, cover once every 10 minutes) 5. Motion Detection Record Under the standby mode, long press top key for 3 seconds, blue lamp will turn off, and then camera will switch to detection standby mode. Once any object moves in front of camera lens, it will start to record automatically. Every recording video lasts 2 minutes then will be saved automatically. After that, the camera will detect again if there’s any moving object or not, and then automatically switch to detection standby mode when detecting nothing, or record with detecting any moving object. Under the motion detection mode, short press top key, blue lamp will be bright constantly, and then camera will quit motion detection mode. (If camera is recording under motion detection mode, then it first saves the video before quitting.) 6. Photograph Under the standby mode, short press “M” key, red lamp flashing once means taking a photo, then camera will save the photo and switch to standby mode. 7. Sound Recording Only Under the standby mode, long press “M” key for 3 seconds, blue lamp will turn off, and the camera will start to record sound only; short press “MODE” key again, blue lamp will turn on, and camera will stop recording and back to standby mode. 8. Time Setting Put camera with TF memory card connect with computer, it will generate automatically a file named as “time” in root directory, open “time” file and rewrite present data and time according to the format in the file, that is （2017.05.20 blank 08:00:00 blank N/Y）, then save the file and restart the camera, time setting will be finished. (Postfix is Y means displaying time watermark, postfix is N means not displaying time watermark. It’s to display time watermark as default.) 9. Camera Parameters Setting Put camera with TF memory card connect with computer, it will generate automatically a file named as “SIZESET” in root directory, open “SIZESET” file and rewrite the parameters; including 6 modes of 10, 11, 20, 21, 30, 31, then save the file and restart camera, parameters setting will be finished. Note: The first number is 1 represents resolution ratio 720*480 The first number is 2 represents resolution ratio 1280X720 The first number is 3 represents resolution ratio 1920X1080 The second number is 1 represents opening cyclic covering The second number is 0 represents closing cyclic covering For an instance: rewrite 30 in SIZESET file that represents resolution ratio 1920*1080 without cyclic covering. 10. Shutdown Under the recording or standby mode, long press “P” key for 3 seconds, release the key, then standby indicator light will turn off, that means the camera has been powered off. 11. Automatic Shutdown Function Under any following condition: camera will automatically save recording video and power off. (1)If the camera is in electricity shortage while recording, the system will firstly save recording video and power off automatically. (2) After start-up, there’s no any operation in 1 minute, the system will automatically power off. 12. Charging While Recording Under the condition of power off, the camera will start up automatically and switch to standby mode (blue lamp is bright constantly) when connecting with charger or portable power source. At this time, camera could have video recording, photograph and motion detection recording. If there’s not any operation in 3 minutes, camera will switch to charging mode automatically. Note: Under the charging while recording condition, the camera is also in the status of charging while power consuming. Therefore, it will cost a long time to make camera fully charged. Please not be charging while recording in order to realize rapid charging, 13. Connecting with Computer If connecting with computer under the condition of power off, the camera could be used as U flash disk, which could copy, cut or delete file optionally. Plug this camera in USB port of computer, the removable disk identification will pop up in several seconds while red indicator light flashing. Note： _ After connecting with computer, if the camera could not identified by computer, or removable disk identification could not pop up after 30 seconds, please re-plug the camera in computer. _ It’s recommended that copy or cut video file to computer and then play it. If directly play saved video file in camera, it may cause play not smoothly owing to overbig data volume and discontinuous transmission. 14. Computer Camera Function Under the start-up condition, use USB wire to connect camera with computer, at this time, camera will switch to computer camera mode. The camera could be used as computer camera by clicking AMCAP icon. 15. Reset When this camera can not work well owing to abnormal operation or other unknown reason, it should reset the camera. The specific operation as follows: it could realize reset operation by pressing both top “O” and “M” key once. If it still could not reset after above operation, please contact with customer service. Thank you! 16. Product Parameters
Note: _ Working temperature: Please use it under natural temperature, and do not let it work under the temperature that human could not tolerate. _ Working humidity: please use it under the environment humidity that is suitable for human living, and do not place it in moist working environment, because this camera does not have water-proof function, please ensure to prevent it from water spraying or raining. _ Shoot illumination: Please use it under the environment having adequate light source, and please not let camera lens directly aim at super strong light source such as sunlight to avoid optical element get damaged. _ Waste Treatment: Please care for the |